Difference between revisions of "Set up a hotspot with Linux"

From Linuxintro
imported>ThorstenStaerk
imported>ThorstenStaerk
Line 1: Line 1:
 
This is an example how to turn your computer into an accesspoint for wireless networks. My typical usecase for this is that I am in a place where I have to [[set up an UMTS connection to the internet]] and I want to share this internet connection as WLAN with others.
 
This is an example how to turn your computer into an accesspoint for wireless networks. My typical usecase for this is that I am in a place where I have to [[set up an UMTS connection to the internet]] and I want to share this internet connection as WLAN with others.
  
 +
= SUSE Linux 12.1 =
 
This guide is based on SUSE Linux 12.1 but should work same or similar for every distribution. We will use the software HostAPD for this.  
 
This guide is based on SUSE Linux 12.1 but should work same or similar for every distribution. We will use the software HostAPD for this.  
  
Line 78: Line 79:
 
  # iptables -A FORWARD -i <html><abbr title="the bridge facing the internal net">br0</abbr></html> -j ACCEPT
 
  # iptables -A FORWARD -i <html><abbr title="the bridge facing the internal net">br0</abbr></html> -j ACCEPT
 
  # iptables -A FORWARD -i <html><abbr title="the interface facing the internal net">wlan0</abbr></html> -j ACCEPT
 
  # iptables -A FORWARD -i <html><abbr title="the interface facing the internal net">wlan0</abbr></html> -j ACCEPT
 +
 +
= Knoppix 7.02 =
 +
sudo apt-get install hostapd
 +
zcat /usr/share/doc/hostapd/examples/hostapd.conf.gz >/etc/hostapd.conf
 +
Now edit the lines in /etc/hostapd.conf:
 +
driver=nl80211
 +
channel=3
 +
hw_mode=g
 +
auth_algs=1
  
 
= See also =
 
= See also =

Revision as of 15:32, 8 July 2012

This is an example how to turn your computer into an accesspoint for wireless networks. My typical usecase for this is that I am in a place where I have to set up an UMTS connection to the internet and I want to share this internet connection as WLAN with others.

SUSE Linux 12.1

This guide is based on SUSE Linux 12.1 but should work same or similar for every distribution. We will use the software HostAPD for this.

what you need

  • a Linux distribution with a kernel greater than about 2.6.30, in this example we use SUSE Linux 12.1
  • a USB wireless adapter, in this example we use a Conceptronic device with a RaLink chipset

what you do

create connectivity

  • plug in your USB wireless network adapter
  • find out how to activate the driver:
linux-noqb:~ # hwinfo --usb
[...]
22: USB 00.0: 0000 Unclassified device
  [Created at usb.122]
  Unique ID: doL0.gHs6xlT8BAF
  Parent ID: FKGF.0j9+vWlqL56
  SysFS ID: /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.6/2-1.6:1.0
  SysFS BusID: 2-1.6:1.0
  Hardware Class: unknown
  Model: "Ralink 802.11 bg WLAN"
  Hotplug: USB
  Vendor: usb 0x14b2 "Ralink"
  Device: usb 0x3c22 "802.11 bg WLAN"
  Revision: "0.01"
  Driver: "rt73usb"
  Driver Modules: "rt73usb"
  Device File: wlan0
  Speed: 480 Mbps
  HW Address: 00:80:5a:4e:1a:eb
  Link detected: yes
  Module Alias: "usb:v14B2p3C22d0001dc00dsc00dp00icFFiscFFipFF"
  Driver Info #0:
    Driver Status: rt73usb is active
    Driver Activation Cmd: "modprobe rt73usb"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #12 (Hub)
  • Activate the driver
modprobe rt73usb
  • Activate the NIC
ifup wlan0
  • Install HostAPD
yast -i HostAPD
  • Do the following settings in /etc/hostapd.conf
driver=nl80211
bridge=br0
channel=3
hw_mode=g
auth_algs=1
Note
channel=3 and hw_mode=g will work on almost all modern wireless USB adapters, however it may be possible to find one that does not work.
  • Start hostapd
hostapd /etc/hostapd.conf
  • verify that you see a wireless LAN with the ESSID test, e.g. on your mobile phone
  • create a network bridge on your computer
  • assign an IP address to your bridge br0 like this:
brctl addif br0 wlan0
ifconfig br0 192.168.0.5
  • set up a dhcp server listening on your network bridge br0. As name server, use 8.8.8.8 which is google's name server in the internet
  • verify you can connect to the LAN test and get an IP address

Set up NAT

Set up NAT like this: 

# echo 1 > /proc/sys/net/ipv4/ip_forward
# iptables -t nat -A POSTROUTING -o <html>ppp0</html> -j MASQUERADE
# iptables -A FORWARD -i <html>br0</html> -j ACCEPT
# iptables -A FORWARD -i <html>wlan0</html> -j ACCEPT

Knoppix 7.02

sudo apt-get install hostapd
zcat /usr/share/doc/hostapd/examples/hostapd.conf.gz >/etc/hostapd.conf

Now edit the lines in /etc/hostapd.conf: 

driver=nl80211
channel=3
hw_mode=g
auth_algs=1

See also

Retrieved from "http://linuxintro.org/index.php?title=Set_up_a_hotspot_with_Linux&oldid=14962"